How telephone works A telephone uses an electric current to convey sound information from your home to that of a friend. When the two of you are talking on the telephone, the telephone company is sending a steady electric current through your telephones. The two telephones, yours and that of your friend, are sharing this steady current. But as you talk into your telephone's microphone, the current that your telephone draws from the telephone company fluctuates up and down. These fluctuations are directly related to the air pressure fluctuations that are the sound of your voice at the microphone. Because the telephones are sharing the total current, any change in the current through your telephone causes a change in the current through your friend's telephone. Thus as you talk, the current through your friend's telephone fluctuates. A speaker in that telephone responds to these current fluctuations by compressing and rarefying the air. The resulting air pressure fluctuations reproduces the sound of your voice. Although the nature of telephones and the circuits connecting them have changed radically in the past few decades, the telephone system still functions in a manner that at least simulates this behavior. The current which powers your telephone is generated from the 48V battery in the central office. The 48V voltage is sent to the telephone line through some resistors and indictors (typically there is 2000 to 4000 ohms in series with the 48V power source). The old ordinary offices had about 400 ohm line relay coils in series with the line. Here is a simplified picture of typical traditional telephone line interface: to Telephone central Telephone equipment Ground -----+ | Hookswitch / COIL 5H +--o/ o-------+ | | )|| ___ Resistor 200 ohm | ____)||( | 2uF | TIP | | )||( Speaker --||----+--o---------------------------o--+ Mic )||(___| Audio Line wire | )|| --||----+--o---------------------------o-----------+----+ 2uF | RING Resistor 200 ohm | COIL 5H | -48V DC ----+ In some old switches there rere no separate reistors after the relay couils. Just a relay with 2x500 ohm coils was uased for both current limiting and the coils between the line wires and the power source. When your telephone is in on-hook state the "TIP" is at about 0v, while "RING" is about -48v with respect to earth ground. When you go off hook, and current is drawn, TIP goes negative and RING goes positive (I mean less negative). A typical off hook condition is TIP at about -20v and ring at about -28v. This means that there is about 8V voltage between the wires going to telephone in normal operation condition. The DC-resistance of typical telephone equipment is in 200-300 ohm range and current flowing through the telephone is in 20-50 mA range. Why 48V voltage is used in telephone systems ? The -48V voltage was selected because it was enough to get through kilometers of thin telephone wire and still low enough to be safe (electrical safety regulations in many countries consider DC voltages lower than 50V to be safe low voltage circuits). 48V voltage is also easy to generate from normal lead acid batteries (4 x 12V car battery in series). Batteries are needed in telephone central to make sure that it operates also when mains voltage is cut and they also give very stable output voltage which is needed for reliable operation of all the circuit in the central office. Typically the CO actually runs off of the battery chargers with the batteries in parallel getting a floating charge. The line feeding voltage was selected to be negative to make the electrochemical reactions on the wet telephone wiring to be less harmful. When the wires are at negative potential compared to the ground the metal ions go form the ground to the wire instead of the situation where positive voltage would cause metal from the wire to leave which causes quick corrosion. Some countries use other voltages in typically 36V to 60V range. PBXes may use as low as 24 Volts and can possibly use positive feeding voltage instead of the negative one used in normal telephone network. Positive voltage is more commonly used in many electronics circuits, so it is easier to generate and electrolysis in telecommunications wiring is not a problem in typical environment inside office buildings. Some older offices employ battery reversal (swap DC feed to tip and ring) to signal off-hook at the remote end. What is sealing current ? The current sent to telephone line as an another advantage besides that it supplies the operating power for your telephone. Telephone practice uses (or did use) twisted splices. These splices did not always make good connections. Placing a small DC bias on a long transmission pair is often done by telecommuncation carriers to reduce poor connections, and noisy lines. The DC bias is often refered to as a "sealing current". So putting DC current through the cable sealed the connection and so improved the transmission. Why full duplex operation in single wire pair ? Full-Duplex is a term used to describe a communications channel which is capable of both receiving and sending information simultaneously. Telephone sets (ordinary analog ones) have only 2 wires, which carry both speaker and microphone signals. The signal path between two telephones, involving a call other than a local one, requires amplification using a 4-wire circuit. The cost and cabling required ruled out the idea of running a 4-wire circuit out to the subscribers' premises from the local exchange and an alternative solution had to be found. Hence, the 4-wire trunk circuits were converted to 2-wire local cabling, using a device called a "hybrid". This function can send and receive audio signals at the same time is accomplished by designing the system so that there is a well balanced circuit in both ends of the wire which are capable or separating incoming audio from outgoing signal. This function is done by telephone hybrid circuit contained in the network interface of the telephone. What is the bandwidth of the telephone line ? A POTS line (in the US and Europe) has a bandwidth of 3kHz. A normal POTS line can transfer the frequencies between 400 Hz and 3.4 Khz. The frequency response is limited by the telephone transmission system (the actual wire from central office to your wall can usually do much more). Nowadays POTS is sharply bandlimited due to the fact that the line almost always is digitally sampled at 8kHz at some point in the circuit. The absolute, theoretical limit (with perfect filters) is therefore 4kHz - but this isn't reality, 3.4 kHz maximum frequency is. The bass frequency response is limted because of the limitations in telephone system components: transfromers and capacitors can be smaller if they don't have to deal with lowest frequencies. Other reason to drop out the lowest frequencies is to keep the possibly strong mains frequency (50 or 60 Hz and it's harmonics) hummign away from the audio signal you will hear. Developed by v0id under Copyright of Smart Development Networks©. All rights reserved.